+ Reply to Thread
Results 1 to 6 of 6
-
09-23-2009 #1
MBc Member
- Join Date
- Jan 2008
- Location
- BHC AZ
- Posts
- 573
- Thanks
- 0
- Thanked 0 Times in 0 Posts
- Rep Power
- 6
A source for the 56 clutch bearings and instructions
I have seen this request go unanswered many times .
I finally found a source for high quality bearings and instructions to install them .
These are the bearings behind the clutch.
http://home.roadrunner.com/~bikeparts/miscellaneous.htm
$8.00 shipped.
Now I will just refer to this post.
-
06-27-2010 #2
MBc Newbie
- Join Date
- Jun 2010
- Age
- 63
- Posts
- 15
- Thanks
- 0
- Thanked 0 Times in 0 Posts
- Rep Power
- 0
link won't work 4 me
is this link ok or what do I need to do?
-
06-29-2010 #3
MBc Member
- Join Date
- Jan 2008
- Location
- BHC AZ
- Posts
- 573
- Thanks
- 0
- Thanked 0 Times in 0 Posts
- Rep Power
- 6
http://www.piratecycles1.com/ is the new supplier for all manic mechanic parts.
Usually put putting around town.
-
06-29-2010 #4
MBc Newbie
- Join Date
- Jun 2010
- Age
- 63
- Posts
- 15
- Thanks
- 0
- Thanked 0 Times in 0 Posts
- Rep Power
- 0
bearings
I don't see the bearings listed there. Lot's of other good stuff,
-
06-29-2010 #5
Senior Member
- Join Date
- Aug 2009
- Location
- So. Cal
- Posts
- 1,698
- Thanks
- 0
- Thanked 0 Times in 0 Posts
- Rep Power
- 5
I don't see anything there. It's just an blue
screen with a couple of silhouetted boxes in it, even with my script blocker turned off.Do not ride faster than your guardian angel can fly!
-
07-01-2010 #6
Senior Member
- Join Date
- Aug 2009
- Location
- Calera, Alabama
- Age
- 66
- Posts
- 1,980
- Thanks
- 0
- Thanked 2 Times in 2 Posts
- Rep Power
- 5
No retail....
http://home.roadrunner.com/~bikeparts/Ron ><)))))*> Calera, Alabama
My store
Pre install HT tips
Political Correctness:
A doctrine fostered by a delusional, illogical liberal minority, and rapidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a turd by the clean end.
Reply With Quote
Similar Threads
-
[Clutch] HT Clutch puck source??
By Pablo in forum Transmission / DrivetrainReplies: 46Last Post: 08-12-2009, 05:46 PM -
Clutch issue: small ball bearings loose in clutch
By Elmstreetmotorized in forum Frame Mounted EnginesReplies: 3Last Post: 04-25-2009, 02:27 PM -
clutch bearings
By gubba in forum Frame Mounted EnginesReplies: 10Last Post: 03-25-2009, 03:57 AM -
following instructions
By mattoo in forum Introduce YourselfReplies: 6Last Post: 11-29-2008, 11:30 AM -
Auto Clutch Needle Bearings:
By Hal the Elder in forum WhizzerReplies: 3Last Post: 11-06-2008, 03:16 PM
